Slide Show Lily Flower
Rate this posting:
Here is a tutorial for one of my favourite flowers. It's not hard to do even if you haven't done any paper folding before. There's just a fair few steps because you have to repeat some of the steps 8 times, but I think it's worth it and you'll have this flower folded in under 15 minutes flat.
1. Start with a square of paper - I suggest NO smaller than 20cm or it will be too fiddly for first timers. Fold the paper in half both ways diagonally and horizontally and vertically to make a star as in the pic below. Ensure all of your creases are sharp and precises as possible by running finger nail along each crease for every step of this model.
2. Now fold the paper (right side out) into a triangle and using the creaselines as a guide begin to push one of the sides in as shown below...
Push one of the sides into the centre of the triangle and repeat with the other side. The result is shown below.
3. Ensure that the open edges of the shape are facing away from you and then take one of the sides and fold into the centre crease line as shown below...
Fold one of the side edges into the center creaseline and repeat with
the other side edge and you will get the result shown below...
Now flip the model over, repeat with the other 2 side edges and unfold all of the edges again and you will get the result shown below...
4. Take one of the folded side edges and slip your
index finger into it as shown in the pic below...
That
scar is the result of a small argument (that I lost) with my olfa cutter - we
suffer for our art! Slip your finger into the side edge/flap (or whatever
you want to call it) and using the creaselines as guide press the flap down so
that you get what looks like a kite with a white tip as shown below...
Now
repeat the previous step with the other 3 flaps and you will get the result as
shown below...
Result: Notice how there are 8 'pages/sides' to the model. some of the 'pages' look like the picture above (with white tip) and other pages look like the pic below...
And others look like this (plain with no white tip) I'm just mentioning the difference in the way the pages look because it's important for the following steps.
5. Ensure the a 'white tip' page is facing up and fold the shape in half by bringing the bottom tip and the top tip together as shown below...
6. Ensuring you have the kite shape with the white tip facing upwards, take one of the top half side edges and (precisely) fold it into the centre crease line as shown below...
Fold the side edge into the centre crease as shown, repeat with the other side, and open out again and you will get the result as shown below...
7. Follow the steps CLOCKWISE from top left in the pic below...
Clockwise from top left: slip your finger into the top edge of the pocket (pic 1) and using the side creaslines as a guide pull the lip of it all the way down (pic 2), ensure everything is aligned on the centre creasline (pic 3), push the small resulting triangle upward on the creasline as shown (pic 4).
Repeat the whole of step 7 for the other 3 sides (with white tips).
8. Nearly there! Ensure you have a plain side (with no folds or flaps etc. on it) facing up and the open tip open edges are facing away from you. Follow the steps CLOCKWISE from top left in the pic below...
Clockwise from top left: plain side is facing up and the open tip ends are facing away from you (pic 1), precisely fold one of the side edges into the centre creaseline and repeat with the other side (pic 2), repeat with step with the other 3 PLAIN sides (pic 3), this should be the result (pic 4).
9. Pick up the model with the side facing you (as in pic 4 of the previous step) and pull one of the petals downwards as shown in the pic below...
As you pull the petal down you'll notice it will only go so far downwards, at the point where it will go no further make a crease at the base of the petal. Flip the model over and repeat on the other side. Open out and repeat for the remaining 2 petals.
10. Grab a pencil or ruler and curl the edge of the petals to make things even more pretty as shown below.
{[['
']]}
']]}
Here is a tutorial for one of my favourite flowers. It's not hard to do even if you haven't done any paper folding before. There's just a fair few steps because you have to repeat some of the steps 8 times, but I think it's worth it and you'll have this flower folded in under 15 minutes flat.
1. Start with a square of paper - I suggest NO smaller than 20cm or it will be too fiddly for first timers. Fold the paper in half both ways diagonally and horizontally and vertically to make a star as in the pic below. Ensure all of your creases are sharp and precises as possible by running finger nail along each crease for every step of this model.
2. Now fold the paper (right side out) into a triangle and using the creaselines as a guide begin to push one of the sides in as shown below...
Push one of the sides into the centre of the triangle and repeat with the other side. The result is shown below.
3. Ensure that the open edges of the shape are facing away from you and then take one of the sides and fold into the centre crease line as shown below...
Now flip the model over, repeat with the other 2 side edges and unfold all of the edges again and you will get the result shown below...
Result: Notice how there are 8 'pages/sides' to the model. some of the 'pages' look like the picture above (with white tip) and other pages look like the pic below...
And others look like this (plain with no white tip) I'm just mentioning the difference in the way the pages look because it's important for the following steps.
5. Ensure the a 'white tip' page is facing up and fold the shape in half by bringing the bottom tip and the top tip together as shown below...
6. Ensuring you have the kite shape with the white tip facing upwards, take one of the top half side edges and (precisely) fold it into the centre crease line as shown below...
Fold the side edge into the centre crease as shown, repeat with the other side, and open out again and you will get the result as shown below...
7. Follow the steps CLOCKWISE from top left in the pic below...
Clockwise from top left: slip your finger into the top edge of the pocket (pic 1) and using the side creaslines as a guide pull the lip of it all the way down (pic 2), ensure everything is aligned on the centre creasline (pic 3), push the small resulting triangle upward on the creasline as shown (pic 4).
Repeat the whole of step 7 for the other 3 sides (with white tips).
8. Nearly there! Ensure you have a plain side (with no folds or flaps etc. on it) facing up and the open tip open edges are facing away from you. Follow the steps CLOCKWISE from top left in the pic below...
Clockwise from top left: plain side is facing up and the open tip ends are facing away from you (pic 1), precisely fold one of the side edges into the centre creaseline and repeat with the other side (pic 2), repeat with step with the other 3 PLAIN sides (pic 3), this should be the result (pic 4).
9. Pick up the model with the side facing you (as in pic 4 of the previous step) and pull one of the petals downwards as shown in the pic below...
As you pull the petal down you'll notice it will only go so far downwards, at the point where it will go no further make a crease at the base of the petal. Flip the model over and repeat on the other side. Open out and repeat for the remaining 2 petals.
10. Grab a pencil or ruler and curl the edge of the petals to make things even more pretty as shown below.
