Paper Crafting

Craftsmanship combined with dramatic silhouette is the hallmark of sculptural artist Zoe Bradley.
Joining elements of sculpure, fashion, and theater, she creates elaborate, oversized silhouettes of highly crafted headpieces, dresses, and sets, often commissioned for advertising campaigns, editorials, catwalk shows, and window installations. Bradley employs traditional tailoring techniques, but offers a twist on the more conentional materials of fashion fabrics with her signature luxury papers. 


Her loe of paper comes from a desire to find a material that can keep its form and is readily and abundantly aailable. She is always looking to push the limits of her material.





1--  Smythson, London, Nancy bag window, 2007.




2 --  Seeds of peace, 2007.
 

3 --  Seeds of peace, 2007.

This is probably the single most fascinating and addictive one-piece technique! Once the basic measurement principles have been grasped, endless variations suggest themselves. To speed up construction, stick squared paper to the back of the card and draw the measurement onto it.


This is the basic Steps form. Note which of the distances are equal and how the mountain and alley creases touch the slits.


1.  Having carefully drawn the construction, cut along the parallel lines.


2.  Use an indenting tool to go over all the creases, beung careful to differentiate valleys from mountains. Then carefully form all the creases simultaneously to collapse the steps into their final shape.


3.  This is how the pop-up should look when the creasing is completed.

4.  Finally, flatten the pop-up and press all the creases firmly.



On a sheet of thin card (cardboard) and using a pencil, draw the gutter crease across the centre. Measure a square grid seven units wide and eight high. Note that the llength of A is twice B.

Using the grid as a guide, draw the steps, as shown. Your drawing must be extremely accurate.



Erase all of the lines that are not needed for the construction. (For clarity, coloured lines hae been used in this example to show which lines are for cutting and which for creasing.)

With this lovely name card, a bird looks as if it has just landed daintily to tell your guest where to sit. Honeycomb paper is available online in a wide range of colors. When you buy it in sheets, you can make lots of paper balls of any  dimension, even the tiniest sizes.


                                                         Supplies

Bird-in-Flight Place Setting templates    Pencil   Card stock   Scissors for paper   Bone folder   Honeycomb paper  Glue   stick   Lightweight paper for bird   Liquid glue.


1.   Download the Bird-in-Flight Place Setting templates at www.chroniclebooks.com/sweetpaper. Using the pencil, trace the card template on card stock. Cut out using the scissors. Fold the card in half and score with the bone folder.


2.   Trace the half-circle honeycomb template on the honeycomb paper, making sure that the lines of the paper are perpendicular to the straight side of the template. Cut out  with the scissors. Using the glue stick, apply glue to each side of the half circle. Line up the straight edge of the half circle
with the folded edge of the card and press to adhere. Open the half circle to form a ball, and attach it to the other side of the card so that it grasps the card. Press to adhere.


3.   Trace the bird template on two layers of lightweight paper. Carefully cut out so that you have two identical birds. Be careful to cut inside the pencil line so that you don’t have to erase it later. Using the glue stick, apply glue to the beak, head, and body of one bird, but not to the wings and tail feathers. Place the other bird on the glue and press firmly all around the bird. Gently bend open the wings and tail feathers.


4.   Apply a thin line of liquid glue to the bottom curve of the bird’s body and gently place the bird on top of the  honeycomb ball, slightly off center, so that the bird looks as if it has just come in for a landing. Hold in place for a few minutes, then allow to dry thoroughly for about an hour.

I (Left) Each strip has an Asymmetric Mountain crease, the placement of which can be determined by measuring the position in relation to the gutter crease. 



The result is a pleasing twisted form.



II (Right) Not every part of the sheet needs to be lifted to become part of a sequence of strips. Here, only every alternate one is lifted.



IIII (Left) Here, the strips are not folded in paralel but are allowed to splay out. 


IV (Right) A platform of any shape can be supported by a series of strips. Note how the second generation is formed. 


The pop-up looks good whether it is on its base or side. 

42, 2008

Yulia Brodskaya was drawn to paper craft because she loves the material itself. For years she collected various kinds of paper, practiced origami, and made collages, paper sculptures, and handmade paper.
More recently, with her signature quilling technique and intricately detailed designs, Brodskaya tries to show the potential for paper craft in general and quilling in particular to be used for a wide variety of creative tasks.

Yulia Brodskaya was drawn to paper craft because she loves the material itself. For years she collected various kinds of paper, practiced origami, and made collages, paper sculptures, and handmade paper. 

More recently, with her signature quilling technique and intricately detailed designs, Brodskaya tries to show the potential for paper craft in general and quilling in particular to be used for a wide variety of creative tasks.

 
                                                             Supplies
 
Party-Time Party Hats templates   Pencil   Scissors for paper   Liquid glue   Ruler   White butcher paper   Glue stick   Ribbon   Crepe paper in various colors


1.   To make the chrysanthemum cone hat: Adhere two pieces of butcher paper using the glue stick. Allow to dry for about 10 minutes. Trace the cone template on the prepared butcher paper and cut out. Roll into a cone. Apply liquid glue along the tab and glue in place. Cut two pieces of ribbon about 20 in/50 cm for ties. Using the liquid glue, adhere the ribbons to the outside of the hat directly across fromeach other.



2.   Stack three colors of crepe paper. Cut a 3-in-/7.5-cm-wide strip, through all layers, long enough to go around the bottom of the hat. Fold the stacked paper lengthwise into fourths. 


 Cut fringe nearly to the center on both long edges of the paper. Apply a very thin line of the liquid glue around the base of the hat about ½ in/12 mm from the bottom. Unfold the paper and attach one strip to the line of glue, being sure to glue the area of the strip without the fringe. 

Apply a line of glue to the center of the first strip and attach the second strip. Repeat with the third strip, using small dots of glue spaced about 2 in/5 cm apart. The liquid glue will warp the crepe paper, but the flowers will cover the warped places in the next step.


3.   Cut a strip of crepe paper 2 in/5 cm wide and 25 in/63.5 cm long. Starting at one end, pleat the strip widthwise to make a flower by pinching the strip of paper and applying glue here and there as you pleat to keep the folds together. 
 Make enough flowers to attach them every 2 in/5 cm around the base of the hat (about nine flowers). Allow the flowers to dry for about 30 minutes.



 Clip the back of the flower to make a flat surface. Apply a dot of glue to the flat surface and press into place on the fringe, holding the flower in place a few  minutes.



4.   Cut a strip of crepe paper about 2 in/5 cm wide and 10 in/25 cm long. Fold lengthwise into fourths. Cut fringe along one unfolded edge nearly to the opposite edge of the strip of paper. Without unfolding the fringed paper strip, pinch it along the bottom of the unfringed edge. Apply a dab of liquid glue to the inside of the hat at the peak of the cone to keep the fringe in place and push the pinched end of the fringe into the hole at the top of the hat. Allow to dry completely, about an hour. Fluff the fringe and push open the flower petals before wearing the hat.

Any occasion that calls for a party certainly warrants party hats—including one that you can pin in your hair. These hats look good on kids and grownups alike. Variations on the embellishments are endless and almost as fun as the party itself!                                                  

                                                     Supplies

Party-Time Party Hats templates     Pencil     Scissors for paper    Liquid glue     Ruler     White butcher paper    Glue stick Ribbon      Crepe paper in various colors


1.   To make the top hat: Trace the three hat templates on card stock and cut out. Shape the walls of the hat into a cylinder. Apply liquid glue to the side tab and glue to the wall, pressing firmly. Hold for about 5 minutes. The top of the hat is wider than the bottom. Bend in the tabs at the top of the hat and apply liquid glue to the tabs. 


 Adhere the top of the hat to the tabs. Next, bend out the tabs on the bottom of the hat and apply liquid glue to the undersides. 

Attach the tabs to the brim. Allow to dry for about 10 minutes.



 2.   Using the hot glue gun, attach the hair clip to the underside of the hat. Allow to dry for about 5 minutes.





3.    (I recommend covering your work surface with newspaper before starting this step.) Pour the thin liquid glue into a small dish. Place the hat upright, and apply a thin layer of thin liquid glue with the foam brush. Working over a scrap paper, cover the hat with glitter. Shake off the excess onto the scrap paper. Check for places that need more glitter, brush with glue, and sprinkle on more glitter. Allow to dry for about an hour. 


4.   Trace the feather template on the magazine paper and cut out. Attach the feather to the hat at the quill with liquid glue, and hold in place to dry for about 5 minutes. Punch out a  circle from your chosen paper.


 Using the glue stick and a dot of liquid glue, glue it to the base of the feather. Allow to dry for about 30 minutes before wearing.

After Single and double Slit techniques, the obvious extension is to use Multi Slits. The technique is ideal for creating beautiful rhythmic abstract, but much of their success depends on accurate measurements, so take time to draw them up and construct them with care!


1.  Fold a stiff piece of paper in half. Using a pencil, carefully draw, then cut, a series of parallel lines, creating a step effect. Note that the two longest lines are the same length.




2.  Begin the creasing by folding back each step one at a time.





3.  Make sure that all the strips lie neatly side by side.



4.  Fold al the steps backwards in the same way, then open the paper. 
 
5.  Create a series of conventional pop-ups, one below the other, by careffully liftting and creasing the steps one at a time.



6.  Close the pop-up and press it firmly to reinforce all the creases.



The narrower the strips, the better the pop-up looks, through if they are too narrow, they become weak and he pop-up looks deflated instead of pert.



 Tiered  Abstract 
Height 11 cm (4,5 in ) 

The many slits of this remarkable pop-up create the illusion of a number of tiered semicircles. Although the effect is complex, the structure is basedon two simple constraints: the length of each slit and the width of the paper between them.